Engines & engine parts

Generator engines and the components that keep them running — including Perkins engine parts.

Overview

Engines & engine parts from Powermec.

A generator is only as reliable as the engine driving it. As the official Perkins distributor in Zimbabwe, Powermec supplies complete Perkins engines, genuine Perkins parts and the workshop support to fit them, from a routine service to a full overhaul.

We support engines in standby and prime generator sets as well as industrial, agricultural and marine applications. Every part is identified against your engine model and serial number, so what you receive fits first time.

400–4000
Perkins power-generation engine series
Genuine
Perkins parts, matched by serial number
Workshop
Repairs, overhauls and load testing
On site
Diagnostics and fault-finding

How an engine works

Six systems keep a diesel engine running.

Most engine problems start in one of these systems. Knowing which one is at fault decides the part, the repair and the cost.

  1. 01

    Base engine

    Block, crankshaft, pistons, liners and cylinder heads carry the combustion load. Wear here shows as oil consumption, blow-by and lost compression.

  2. 02

    Fuel system

    Lift pump, injection pump, injectors and filters meter fuel precisely. Dirty or wet fuel is the most common cause of injector and pump failure.

  3. 03

    Air and turbocharging

    Air filters, turbocharger and charge-air cooler supply clean air for combustion. A restriction means black smoke and lost power.

  4. 04

    Cooling

    Radiator, water pump, thermostat and hoses hold working temperature. Overheating is one of the fastest routes to head-gasket and liner damage.

  5. 05

    Lubrication

    Oil pump, filter and cooler protect bearings and moving parts. Oil pressure and oil condition are the engine’s early-warning system.

  6. 06

    Electrical and control

    Starter, charging alternator, sensors and ECU start the engine, keep batteries charged and feed the protection system.

Product range

What we supply.

Send your model and serial number and our parts team confirms the correct part and price.

Complete engines

Perkins diesel engines for generator, industrial, agricultural and marine use.

  • Perkins 400, 800, 1100, 1200, 1500 and 2000 Series
  • Power-generation engines up to the 4000 Series
  • Replacement and repower engines

Engine parts

The internal components behind a repair or rebuild.

  • Cylinder heads, blocks, pistons and liners
  • Crankshafts, camshafts and bearings
  • Gaskets and seals

Fuel, air and electrical

The systems that feed, breathe and control the engine.

  • Injectors and fuel pumps
  • Turbochargers and air filters
  • Starters, alternators, sensors and ECUs

Service and overhaul kits

Everything a scheduled service or rebuild needs, in one order.

  • Routine maintenance kits
  • Top-end and major overhaul kits
  • Filters for every service interval

Our services

More than parts on a shelf.

Diagnostics and fault-finding

On site or in our workshop, we find the cause before any part is replaced.

Scheduled servicing

Oil, filters, belts and inspections at the intervals your engine needs.

Top-end and full overhauls

Workshop rebuilds with genuine parts, from cylinder-head work to a complete engine.

Engine replacement and repower

Supply, fit and commission a new engine when an overhaul no longer makes sense.

Load testing

Prove the engine and generator under load after a repair or as part of maintenance.

Parts identification

Send the model and serial number and we identify the correct genuine part.

Fault guide

What your engine is telling you.

Common symptoms, what usually causes them and how we deal with each one.

SymptomLikely causesWhat we do
Black smokeBlocked air filter, faulty injectors, turbocharger problems or overloadingCheck the air system, test injectors and confirm the load
Blue or grey smoke, rising oil useWorn rings, liners or valve guides, or a leaking turbo sealCompression and blow-by tests, then plan an overhaul
White smokeCoolant entering the cylinders, injection timing, or running coldPressure-test the cooling system and inspect the head gasket
Hard startingWeak batteries or starter, air in the fuel, or a worn injection pumpTest the starting circuit and bleed and check the fuel system
OverheatingBlocked radiator, failed thermostat or water pump, slipping beltClean and test the cooling system and replace failed parts
Low oil pressureLow or diluted oil, blocked filter, worn bearings or oil pumpStop the engine, then check oil, filter and pressure sender before running
KnockingBearing wear, injector faults or abnormal combustionStop and inspect: running on risks major damage

Repair, overhaul or replace

The right level of work for your engine.

We inspect and measure first, then recommend the option that restores reliability at the lowest overall cost.

  1. 01

    Repair

    One failed component, such as an injector, pump, sensor or gasket, on an otherwise healthy engine.

  2. 02

    Top-end overhaul

    Compression loss or smoke traced to the cylinder head: valves, seats, guides and gaskets.

  3. 03

    Full overhaul

    Wear throughout the engine, with a block and crankshaft that can be reused.

  4. 04

    Replacement

    A damaged block or crankshaft, or an overhaul cost close to that of a new engine.

Maintenance advice

Technician tips.

  • Monitor oil consumption and blow-by as early wear indicators
  • Plan top-end overhauls by running hours, not failure
  • Always replace gaskets and seals when opening an engine

Getting the right part

What to send our parts team.

  • Engine model and serial number, from the engine’s identification plate
  • Generator make and kVA rating, if the engine drives a generator
  • Running hours
  • The symptoms and when they started
  • Photos of the engine plate and any damaged part
  • Where the engine is installed
  1. 01

    Share your details

    Engine or generator model, serial number and the part you need.

  2. 02

    We confirm fit

    Our parts team checks compatibility, price and stock.

  3. 03

    Collect, deliver or fit

    Collect, arrange delivery, or have our technicians fit it.

FAQ

Common questions.

Can you overhaul my engine?

Yes. Our workshop handles top-end and full overhauls with parts supplied in-house.

What details do you need?

Engine model, serial number and generator rating help us confirm the correct parts.

Do you sell complete Perkins engines?

Yes. As the official Perkins distributor in Zimbabwe we supply Perkins engines for generator, industrial, agricultural and marine use. Tell us the application and we confirm the right model.

Where do I find the engine serial number?

On the engine’s identification plate, usually on the side of the block. A clear photo of the plate is the quickest way to get the right part.

Should I overhaul or replace my engine?

We inspect and measure first. An overhaul makes sense when the block and crankshaft can be reused; replacement is better when they are damaged or the overhaul cost approaches a new engine.

How do I get the parts?

Collect from us, arrange delivery, or have our technicians fit them as part of a service or repair.

Plan the next step

Tell us what needs power.

Our team will review the application and route your enquiry to the right solution.